5. MAP TERMINAL USAGE 5.01 The entry of commands described in this Practice is based on a DEC VT-1001 video display unit. Some variations in identification of keyboard keys apply when other types of termi- nals are used. THE CARRIAGE RETURN KEY. 5.02 The carriage return (CR) key is identified in different ways (such as ENTER, RETURN, CARRIAGE RETURN) on various types of terminals. It is always used to enter commands and parameters into the system after the information is typed into the input echo area, and edited if necessary. 5.03 Two successive operations of the CR key, without typing additional input, displays the version of software being used in the command interpreter output area. It consists of the N.T. Purchase Order (PO) number; office location; software release number; software production status; and release date (yymmdd). A typical response is: F35681 O'CONNOR TOLL BCS-14 RTM 840323 Where: DISPLAY DESCRIPTION F35681 N.T. PO number O'Connor Toll office location BCS-14 software release number RTM software production status "Ready to Manufacture" 840323 release date Mar. 23, 1984 THE CURSOR 5.04 The cursor is a short line, or a small rectangle, that is displayed on the screen. A character that is typed in is displayed above the line or in the rectangle, and the cursor moves one space to the right in readiness for the next character. When the CR key is pressed the cursor returns to the start of the line in readiness for additional characters. 5.05 The cursor may be changed from a line to a rectangle (or the reverse) and from a steady state to a flashing state (or the reverse) by procedures described in the terminal manufac- turer's manual. 1 DEC VT-100 is a trademark of Digital Equipment Corporation. Page 26 PRACTICE 297-1001-520 RELEASE: 02.03 LOGGING-IN AT THE MAP 5.06 To use a MAP terminal it is first necessary to carry out a logging-in procedure. The procedure maintains the securi- ty of the system by limiting access to authorized personnel. 5.07 Log-in procedures may vary for different types of termi- nals, and depend on security features that are in effect. A typical sequence of log-in actions and responses for general purpose terminal is as follows: ACTION RESPONSE depress the BREAK key - terminal beeps type LOGIN - screen displays the command LOGIN depress the CR key - screen displays a request for user name and password enter user name and password - screen displays CI: and > on two consecutive lines of other- wise blank screen. 5.08 When the log-in procedure is successfully completed, CI: and > are displayed. 5.09 User names and passwords known to the system can be changed by authorized personnel to maintain the security of the system. See 297-1001-129. COMMUNICATION LANGUAGE 5.10 The language of communication between the terminal and the system is associated with the user name. The language can be changed by the user to another language that is prescribed for that machine. Table C on page 28 contains the procedures that are used to change from English to French, and from French to English. 5.11 When the office is not equipped with feature package NTX066AA, and an attempt is made to change the MAP lan- guage, the following response is displayed: LANGUAGE LOADED IS ENGLISH Page 27 PRACTICE 297-1001-520 RELEASE: 02.03 TABLE C PROCEDURE TO CHANGE MAP LANGUAGE LANGUAGE CHANGE ENTER RESPONSE _________________________________________________________________ English to French BMMI BMMI: ISPEAK FRENCH IHMB: MAINTENANT LA LANGUE FRANCAISE EST UTILISEE LAISSER (The system will now respond in French to French commands) French to English IHMB IHMB: JEPARLE ANGLAIS BMMI: YOU ARE NOW SPEAKING ENGLISH LEAVE (The system will now respond in English to English commands) LOCKED KEYBOARD 5.12 During system activity, such as a previously requested function that has not been completed, the terminal beeps in response to any further inputs, indicating that the keyboard is locked until the activity is complete. During the period that the keyboard is locked, all information that is typed-in is ignored. 5.13 When a system reload is in process, the keyboard remains locked until the reload is complete. At that time the log-in procedure is required for all MAP except the main mainte- nance position, called the OPERATOR position, as identified in the ID area of the operator position MAP display. Page 28 PRACTICE 297-1001-520 RELEASE: 02.03 RESPONSE MESSAGES 5.14 Responses to commands originate in the system and in the maintenance subsystems, and are interpreted and handled by the Command Interpreter. 5.15 If the requested function is successfully completed, the prompt symbol (>) is displayed in the input echo area after the function response is displayed in the command inter- preter output area. If the requested function fails to complete, the reason for the failure is displayed in the command interpret- er output area, and a fault report is issued to identify the source of the failure. 5.16 If a terminal starts to output (for example a MAP update) when a user is typing in, the user can continue to type, but the characters will not appear in the input echo area of the display until the terminal output is complete. The Response "MORE..." 5.17 When the amount of output generated in response to a com- mand exceeds the capacity of the CI display area of the MAP, the response MORE... is displayed at the bottom line of the screen, or at the bottom line of the CI output area when in the MAPCI mode. Depressing the CR key causes the next full screen of response data to replace the current display. Additional output is displayed with each CR key operation until the last display is identified by the absence of the response MORE... 5.18 The response MORE... is also displayed at the bottom line of the CI output area of the MAPCI and subtending menus when prompts are displayed for missing parameters. The response is discontinued when the missing parameter or the command ABORT is entered. The MORE... display remains until a valid input is entered; it will not time out. 5.19 Any of the BREAK commands can be typed in response to MORE... without first operating the BREAK key. COMMAND MENU DESCRIPTION 5.20 Valid commands and parameters are represented by codes displayed in the menu area. A unique one or two digit menu number is assigned to each code and is displayed to the left of the code. A total of eighteen menu numbers are available for each subsystem and all of them are displayed. When a command or parameter has not been assigned to a menu number, the number is displayed alone and cannot be used. 5.21 Command and parameter codes are abbreviations of one or more words which describe the function. In the menu, the first letter of each word is capitalized, and any additional let- ters in the word are normally shown in the lower case. For exam- Page 29 PRACTICE 297-1001-520 RELEASE: 02.03 ple the command TEST is abbreviated and displayed as Tst, and the command to replace spare equipment is displayed as SpRepl. Simi- larly, the Return To Service function is displayed as RTS. 5.22 Commands and parameters in the menu include the underscore character (_) to indicate the following qualifications for their use: Tst_ a command which requires a parameter _Spare a parameter _Card_ a parameter which requires another parameter Sync a command which does not require a parameter Quit a command which accepts, but does not require a non-menu parameter, e.g. ALL. ENTERING COMMANDS 5.23 Commands are entered in one of the following ways: o the menu number is typed in, followed by a CR operation. o the command code is typed in, character-by-character without regard to upper or lower case format, followed by a CR. Underscores are not typed in. 5.24 If the command requires a parameter and the parameter code is displayed in the menu, the parameter may be entered by menu number or by parameter code. If the command menu number has been entered, the parameter menu number can be entered. If the command code has been entered, the parameter code must be entered. When replying to a prompt for parameters, the first character to be typed in must always be a space, followed by the required parameter. 5.25 Some examples of command entry requirements, based on CMC subsystem menu items 6 (Tst_) and 10 (_Card_), that illus- trate these rules are: Valid Entries 610 6CARD 6 CARD TST CARD Invalid Entries o 6 10 menu number typed in after a non-numeric TST 10 character such as a space o TST__CARD_ underscores displayed in the menu are entered Page 30 PRACTICE 297-1001-520 RELEASE: 02.03 5.26 Commands entered with incorrect characters or spacing are interpreted as non-existent commands. They cause the text NO SUCH COMMAND to be displayed in the command interpreter output area indicating that there is no such command. 5.27 Sometimes, non-menu parameters are entered after a menu command or parameter. If only menu numbers are entered, the first non-menu parameter can be entered immediately after the last menu number, with or without an intervening space. Any additional non-menu parameters must be preceded by a space. If the command or parameter code was typed in, a space must precede the non-menu parameter. Some examples based on CMC subsystem menu items 0 (Quit), 6 (Tst_) and 10 (_Card_), that illustrate these rules are: Valid Entries o 6100 2 test card 2 of CMC 0 610 0 2 TST CARD 0 2 o 0ALL exit from maintenance system MMI 0 ALL QUIT ALL Invalid Entries o TST CARD0 2 no space before the first non-menu parameter 6CARD0 2 (0 in these cases) when the command or parameter code is typed in. MULTIPLE COMMAND ENTRIES 5.28 A series of commands, each separated by a semicolon (;), can be typed in and then entered with one CR operation. Such a series is referred to as a string, or chain, of commands. They can be used within a subsystem, and to move to other subsys- tems. Command strings are comprised of letters, numbers, and punctuation symbols (including spaces), or a combination of them. When the MAP is used the menu item number for the first command and its parameter may be typed in, followed by the remaining com- mands and parameters typed in full. When a line-at-a-time device (such as a teleprinter) is used, all command and parameter codes must be typed in full. When a letter or symbol is typed in, menu numbers can no longer be used in that command string. 5.29 An example of a command string entry from the CMC subsys- tem is CC;PS 0;TST CONT 1; CMC In this example the following series of actions occur: o the CC subsystem is accessed o the PS level of CC subsystem side 0 is accessed o the controller of PS1 is tested Page 31 PRACTICE 297-1001-520 RELEASE: 02.03 o the CMC subsystem is reaccessed. COMMANDS FROM OTHER MENUS 5.30 Commands and parameters from menus other than the one dis- played can be entered if: o commands and parameters that are entered reside in higher level menus than the one that is displayed o the commands and any parameter codes are typed in full o the command code does not appear in this displayed menu (oth- erwise it is invoked at the displayed level). For example, the CMC maintenance subsystem can be accessed from the PS level of the CC subsystem by entering the MTC menu command CMC. EDITING LINES THAT ARE INPUT 5.31 Commands and parameters that are typed in and displayed in the input echo area can be edited before the CR is pressed. Editing functions include deleting and inserting char- acters and lines, and changing the horizontal position of the cursor. Terminal controller firmware in the NT1X67BC circuit card is required for editing functions. The installed version of the terminal controller firmware can be determined by pressing the BREAK key and then typing VERSION followed by the CR func- tion. Refer to Paragraph 5.32 on page 35. LINE EDITING COMMANDS 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � CONTROL + � F � � (KEY) � U � � � E � � � I � � � X � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Edits the typed-in line before it is entered. Where: F moves the cursor to the right one position. U deletes the entire typed-in line Page 32 PRACTICE 297-1001-520 RELEASE: 02.03 E deletes all typed-in characters from the cursor posi- tion to the end of the line I places the terminal in the mode to insert subsequently typed characters into the line. As each inserted char- acter is typed in, the character at the cursor posi- tion, and all the characters to the right of it, move one position to the right. X exits from the character insert mode. Responses: The input echo area display is altered in accordance with the applied editing functions before the information is entered. Notes: 1. The plus symbol (+) indicates that the control key must be pressed and held until the editing function that is being invoked is activated. Release of the control key before the character key that activates the function causes a series of the characters to overwrite those displayed at the cursor position in the input echo area. 2. Each attempt to insert a character when the cursor is posi- tioned at the end of the line causes the terminal to beep. 3. Existing characters to the right of the cursor position are repositioned to the right as characters are inserted. 4. When the character insert mode has been exited by releasing the CONTROL and letter keys, subsequent characters that are typed in overwrite characters existing at the cursor posi- tion. 5. If there are no characters from the cursor position to the end of the line, character deletion attempts cause the termi- nal to beep. 6. When the cursor is at the end of the typed-in line, each attempt to move it to the right (CONTROL KEY+F) causes the terminal to beep. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � ? � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Recalls one of the last three lines that were entered. Page 33 PRACTICE 297-1001-520 RELEASE: 02.03 Responses: � The recalled line is displayed in the input echo area. � The character ? is displayed in the CI output area. Notes: 1. The character ? must be in the first position in the input echo area to be valid. 2. The CR key is depressed to display the recalled line. 3. The first line recalled is the most recent line entered. 4. Immediate repeat of steps in notes 1 and 2 recalls the second most recent line entered. 5. Second immediate repeat of steps 1 and 2 recalls the third most recent line entered. 6. When additional successive recall commands are entered, the lines mentioned in notes 3, 4 and 5 are successively dis- played. 7. All characters in the input echo area are displayed in the command interpreter area when the recall command is entered. 8. Exit from recall is achieved by entering CTRL + U. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � BACK SPACE � � � (key) � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Moves the cursor to the left Responses: The cursor displayed in the input echo area moves one position to the left. Notes: 1. The backspace key can be designated BACK SPACE or <-- or BS 2. Each operation of the backspace key moves the cursor one position to the left. 3. The cursor moves to the left repeatedly when the backspace key is held operated, if the terminal has an auto-repeat fea- ture. 4. When the cursor is in the left-most position, a backspace attempt causes the terminal to beep. Page 34 PRACTICE 297-1001-520 RELEASE: 02.03 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � DELETE � � � (KEY) � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Deletes a valid character Responses: The valid character at the cursor position is deleted from the input echo area display. Note: Each delete attempt when the cursor is at a space causes the terminal to beep. CHANGING OUTPUT DISPLAYS 5.32 Processes that are invoked by MAP commands can be started and stopped, and the display of system outputs changed, by operating the BREAK key before typing in specific command codes. These codes are listed below with a description of their use. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � � HT � � � RT � � BREAK � STOP � � (key) � HX � � � HXX � � � CLEAR � � � LED � � � LEE � � � VERSION � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Changes MAP displays Where: HT (Halt Typing) discontinues the progressive display of responses to commands that are invoked. RT (Resume Typing) resumes the progressive display of responses to commands that are invoked (exit from Halt Typing mode). STOP clears the screen and exits to the CI: level HX an alias for STOP HXX an alias for STOP CLEAR clears the screen and discontinues the display of menus and headers during input and output activities, while maintaining the level that was accessed. Page 35 PRACTICE 297-1001-520 RELEASE: 02.03 LEE enables line editing functions. LED disables the line editing functions (exiting from line editing function). VERSION displays the version number of the terminal controller firmware. Responses: Specific responses to each code that is entered are as follows: Code Response _______ ________ HT output displays in the CI area are discontinued RT output displays in the CI area are resumed STOP all screen displays are cleared and CI: > is displayed in the upper left corner of the screen HX the same as STOP HXX the same as STOP CLEAR input and output displays in all areas continue without headers or menus LEE line displays in the input echo area can be edited (see Paragraph 5.31 on page 32) LED line displays in the input echo area cannot be edited (see Paragraph 5.31 on page 32) VERSION the version number of the terminal controller firmware being used by the terminal is displayed in the CI area, e.g. VERSION = 1 Notes: 1. The terminal beeps each time the BREAK key is operated. 2. The code HT discontinues the display of process responses, starting with the response when the code is entered, without affecting the process or responses in any other way. 3. The code RT resumes the display of process responses, start- ing with the response when the code is entered, without affecting the process or responses in any other way. 4. The codes HX and HXX function in the same way as STOP. Page 36 PRACTICE 297-1001-520 RELEASE: 02.03 5. When STOP is used, there is an 8 to 10 second delay before the screen returns to the CI: display. 6. Menu numbers cannot be used when the terminal is in CLEAR mode. 7. Exit for CLEAR is QUIT ALL which returns the screen to CI:. Only a typed-in command is valid. 8. Line editing functions are in active mode by default. COMMAND INFORMATION 5.33 Online command information is available that describes the function of the command and indicates the parameters that may be used. A description of how to access this information is contained in Non-Menu Command Q on page 39. The syntax that is displayed for the parameters uses the following symbols: <> angle brackets enclose a required parameter [] square brackets enclose one or more optional parameters {} braces enclose a list of one or more parameter values, or a description of a parameter. 5.34 A parameter value is the actual text which must be typed in instead of the wording in <> or []. A parameter description is usually a range of numeric values, one of which must be typed in. 5.35 The following example shows how a command syntax description that is displayed on a MAP is interpreted: ALMSTAT Parms: [ {D, F, S, N, PSPD} {0 to 32767} {0 to 32767} {0 to 32767}] 5.36 In this example one of the alarm condition parameters D, F, S, N, PSPD may be entered so that the alarm thresholds may be changed. The required minor alarm threshold parameter is then set between the range of parameter values from 0 to 32767. Similarly the major alarm threshold and the critical alarm thres- hold is set between 0 and 32767. Page 37 PRACTICE 297-1001-520 RELEASE: 02.03 PROMPTS FOR MISSING PARAMETERS 5.37 Many commands require the entry of parameters. The system prompts the user to enter the missing or incorrect parame- ters by displaying the following information in the command interpreter output area using the symbols discussed in Paragraph 5.33 on page 37: o the name of the missing parameter o a syntax statement that includes: � the exact spelling if it is required � the allowable range of values. 5.38 An example of a sequence of prompts for missing parameters is: ENTRY PROMPT _____ ______ MAPCI;MTC;CC;DS ENTER: :CC NUMBER> 0 Wrong type: :CC NUMBER>{0 to 1} Enter: :CC NUMBER> (space)0 no further prompts Notes: 1. Capital letters denote the actual characters that are to be entered. 2. The system continues to prompt the user to supply missing parameters until the information is supplied, or until the command ABORT is entered. 3. A space is required before a prompted parameter 0 (zero). CONFIRMATION REQUEST 5.39 Certain commands require additional action by the user before they can be executed. A message is displayed in the CI output area of the MAP, describing the effect of the com- mand if it is executed, and requesting confirmation of intent to proceed. The message is phrased: Please confirm (YES or NO). A YES entry executes the command, while a NO entry cancels the com- mand and clears the CI area of the screen. Confirmation requests are repeated until one of YES, NO or ABORT is entered. ABORT responds in the same way as NO. Page 38 PRACTICE 297-1001-520 RELEASE: 02.03 NON-MENU COMMANDS 5.40 There are non-menu commands available at any level in every maintenance subsystem at all times. Some non-menu commands are exclusive to particular subsystems, while CI com- mands can be used at any level. Because these commands do not appear on a menu, they must be typed in full. Most of the com- mands are not used in day-to-day system maintenance activities and are not described in this Practice. The exceptions are described in the paragraphs which follow. Non Menu Commands in General Use 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � SIL � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Silences the audible alarm. Responses: All flashing alarm indicators that are displayed in the system status area are stopped, and remain in the steady state, and the audible alarm is stopped. Notes: 1. Additional alarms that are displayed after SIL has been entered can be silenced by re-entering SIL. 2. Operation of the non-locking alarm reset key on the alarm control and display panel achieves the same result as enter- ing the SIL command at the MAP. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � Q � command � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Queries the function and format of any command Where: command the command is at the accessed level or a higher level. Responses: A description of the command and its syntax is displayed in the CI output area of the MAP. Explanation: The information displayed explains the purpose of the command and lists the required and optional parameters. Page 39 PRACTICE 297-1001-520 RELEASE: 02.03 NO COMMAND IN LINE Explanation: This response is displayed if one of the following events has occurred. o a menu number has been queried o a queried command is not in the accessed level or an earlier level o a queried command is misspelled User Action: o type in queried command in full o access the level that contains the command being queried. o query properly spelled command Notes: 1. Commands which have a function or format that is unique to a particular maintenance subsystem cannot be queried outside the subsystem. 2. A space is required between Q and the command being queried. 3. "Q" cannot be queried. Q is not actually a command; it is a parameter in front of the specified command. 4. When a command is typed in, a check is made to see if some- thing was typed "in front of" the command. If Q or any string of characters was typed, the command is not executed. Instead, a brief description of the command and the syntax is displayed. Example: When Q RTS is entered in the CC subsystem, the output in the CI output area is: RTS_ -- RETURN TO SERVICE CC LINKS PARMS: <_LINK_> {LINK CMC NUMBER} {0 to 1}} 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � ABORT � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Terminates a command that has been entered previously with incom- plete or incorrect parameters. Page 40 PRACTICE 297-1001-520 RELEASE: 02.03 Responses: The CI output area of the MAP screen is cleared, and ABORT is displayed. Notes: 1. ABORT is valid only in response to a request for parameters or for a confirmation request. 2. The system repeatedly requests the entry of the missing or incorrect non-optional parameter until it is supplied, ABORT is entered. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � MAPCI � [NODISP] � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Places the VDU in the MAP mode of operation. Where: NODISP Provides access to the NODISP mode. (See section 4.04) Responses: The MAP screen displays in the menu area the systems that are available. (See Figure 5 on page 17). Note: The command is valid only after LOGIN or QUIT ALL. MAPCI MENU COMMANDS 5.41 The highest level of MAP commands, MAPCI, is used to gain access to the available maintenance and administration menu of commands. They are described in the paragraphs that fol- low, and are shown in Figure 5 on page 17. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � MTC � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Accesses the maintenance subsystem. Responses: The MAP displays the status of the system in the top three lines of the screen; and, in the menu area, the subsystems that can be accessed. Note: Item 2 in the MAPCI menu may be entered instead of the command MTC. Page 41 PRACTICE 297-1001-520 RELEASE: 02.03 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � SASelect � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for service analysis Responses: The MAPCI menu display is replaced with the SASelect menu display. Service analysis headers and data are displayed in the CI area. Notes: 1. Item 3 in the MAPCI menu may be entered instead of the com- mand SASelect. 2. A detailed description of Service Analysis is provided in 297-1001-471. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � NWM � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for network management. Responses: The MAPCI menu display is replaced with the NWM menu display. NWM headers and data are displayed in the CI output area. Notes: 1. Item number 4 in the MAPCI menu may be entered instead of the command NWM. 2. A detailed description of NWM MMI is provided in 297-1001-453. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � CPSys � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for Call Processing System dis- play. Responses: The MAPCI menu display is replaced with the call pro- cessing system menu display. Call processing headers and data are displayed in the CI output area. Notes: 1. Item 5 in the MAPCI menu may be entered instead of the com- mand CPSys. Page 42 PRACTICE 297-1001-520 RELEASE: 02.03 2. A detailed description of the CPSys MMI is provided in 297-1001-519. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � IBNMEAS � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for Integrated Business Network measurements. Responses: The MAPCI menu display is replaced with the INBMEAS menu display. IBN headers and data are displayed in the CI area. Notes: 1. Item 6 in the MAPCI menu may be entered instead of the com- mand IBNMEAS. 2. A detailed description of the IBNMEAS MMI is provided in 297-1001-320. MTC MENU COMMANDS 5.42 The highest level of maintenance commands, MTC, is used to gain access to the available maintenance subsystem menu of commands. They are described in the paragraphs that follow. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � � � � � � � 쿌LL� � � � 쿛M � � � QUIT � 쿻 � � � � �1 � � � � � � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Retreats from the current maintenance level to a higher level. Where: ALL Achieves direct exit from any MAP level to CI. PM returns the display from any PM level to the MTC level. n is a specified number of retreat levels from the cur- rent level. The range of values is 1 to 5. 1 achieves retreat to the next higher level. It is the default parameter value. Page 43 PRACTICE 297-1001-520 RELEASE: 02.03 Responses: The MAP display of the current level is completely replaced with that of the level retreated to. Notes: 1. Item 0 in any of the menus may be entered instead of the com- mand QUIT. 2. Before the current level display is replaced, the name of the level being retreated to is displayed in the CI output area under the command entered. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � ACTIVITY � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for switch activity. Responses: The MTC menu display is replaced with the activity menu display. Switch activity headers data are displayed in the CI input area. Notes: 1. Item 2 in the MTC menu can be entered instead of the command ACTIVITY. 2. The system status display is retained and continues to be updated. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � BERP � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� The MTC menu display is replaced with the bit error rate perform- ance (BERP) menu display. Bit error rate statistics appear in the CI output area of the display followed by the command input prompt: BERP. Notes: 1. Item 5 in the MTC menu can be entered instead of the command BERP. 2. The system status display is retained and continues to be updated. Page 44 PRACTICE 297-1001-520 RELEASE: 02.03 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � CPSTATUS � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� The MTC menu display is replaced with the call processing status (CPSTATUS) menu display. Call processing statistics appear in the CI output area of the display followed by the command input prompt: CPSTATUS. Notes: 1. Item 6 in the MTC menu can be entered instead of the command CPSTATUS. 2. The system status display is retained and continues to be updated. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � CC � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for Central Control maintenance. Responses: The MTC menu display is replaced with the CC menu display. CC headers and data are displayed in the CI area. Notes: 1. Item 9 in the MTC menu may be entered instead of the command CC. 2. The system status display is retained and continues to be updated. 3. A detailed description of the CC MMI is provided in 297-1001-511. 4. A DMS switch may be configured with a Central Control and a Central Message Controller (CC/CMC) or with a Message Switch and a Computing Module (MS/CM). The CC command is used only in the CC/CMC configuration. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � CM � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for Computing Module mainte- nance. Page 45 PRACTICE 297-1001-520 RELEASE: 02.03 Responses: The MTC menu display is replaced with the CM menu display. CM headers and data are displayed in the CI area. Notes: 1. Item 9 in the MTC menu may be entered instead of the command CM. 2. The system status display is retained and continues to be updated. 3. A detailed description of the CM MMI is provided in 297-1001-529. 4. A DMS switch may be configured with a Central Control and a Central Message Controller (CC/CMC) or with a Message Switch and a Computing Module (MS/CM). The CM command is used only in the MS/CM configuration. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � CMC � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for Central Message Controller maintenance. Responses: The MTC menu display is replaced with the CMC menu display. CMC headers and data are displayed in the CI area. Notes: 1. Item 10 in the MTC menu may be entered instead of the command CMC. 2. The system status display is retained and continues to be updated. 3. A detailed description of the CMC MMI is provided in 297-1001-512. 4. A DMS switch may be configured with a Central Control and a Central Message Controller (CC/CMC) or with a Message Switch and a Computing Module (MS/CM). The CMC command is used only in the CC/CMC configuration. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � MS � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for Message Switch maintenance. Page 46 PRACTICE 297-1001-520 RELEASE: 02.03 Responses: The MTC menu display is replaced with the MS menu display. MS headers and data are displayed in the CI area. Notes: 1. Item 10 in the MTC menu may be entered instead of the command MS. 2. The system status display is retained and continues to be updated. 3. A detailed description of the MS MMI is provided in 297-1001-530. 4. A DMS switch may be configured with a Central Control and a Central Message Controller (CC/CMC) or with a Message Switch and a Computing Module (MS/CM). The MS command is used only in the MS/CM configuration. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � IOD � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for maintenance of Input/Output devices. Responses: The MTC menu display is replaced with the IOD menu display. IOD headers and data are displayed in the CI area. Notes: 1. The item number 11 in the MTC menu can be entered instead of the command IOD. 2. The system display is retained and continues to be updated. 3. A detailed description of the IOD MMI is provided in 297-1001-513. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � NET � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for network maintenance. Responses: The MTC menu display is replaced with the NET menu display. NET headers and data are displayed in the CI area. Page 47 PRACTICE 297-1001-520 RELEASE: 02.03 Notes: 1. Item 12 in the MTC menu may be entered instead of the command NET. 2. The system status display is retained and continues to be updated. 3. A detailed description of the NET MMI is provided in 297-1001-514. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � PM � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for Peripheral Module mainte- nance. Responses: The MTC menu display is replaced with the PM menu display. PM headers and data are displayed in the CI area. Notes: 1. Item 13 in the MTC menu may be entered instead of the command PM. 2. The system status display is retained and continues to be updated. 3. A detailed description of PM MMI is provided in 297-1001-515. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � CCS � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for Common Channel Signalling maintenance. Responses: The MTC menu display is replaced with the CCS menu display. CCS headers and data are displayed in the CI area. Notes: 1. Item 14 in the MTC menu may be entered instead of the command CCS. 2. The system status display is retained and continues to be updated. 3. A detailed description of the CCS MMI is provided in 297-1001-528. Page 48 PRACTICE 297-1001-520 RELEASE: 02.03 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � LNS � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for lines maintenance. Responses: The MTC menu display is replaced with the LNS menu display. LNS headers and data are displayed in the CI area. Notes: 1. Item 15 in the MTC menu may be entered instead of the command LNS. 2. The system status display is retained and continues to be updated. 3. A detailed description of LNS MMI is provided in 297-2101-516. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � TRKS � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for trunk maintenance. Responses: The MTC menu display is replaced with the TRKS menu display. TRKS headers and data are displayed in the CI area. Notes: 1. Item 16 in the MTC menu may be entered instead of the command TRKS. 2. The system status display is retained and continues to be updated. 3. A detailed description of TRKS MMI is provided in 297-1001-516. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � EXT � � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� Requests status display and menu for external alarms maintenance. Page 49 PRACTICE 297-1001-520 RELEASE: 02.03 Responses: The MTC menu display is replaced with the EXT menu display. EXT alarms headers and data are displayed in the CI area. Notes: 1. Item 17 in the MTC menu may be entered instead of the command EXT. 2. The system status display is retained and continues to be updated. 3. A detailed description of EXT MMI is provided in 297-1001-517. Page 50 PRACTICE 297-1001-520 RELEASE: 02.03